{"id":25368,"date":"2026-11-04T21:30:00","date_gmt":"2026-11-04T13:30:00","guid":{"rendered":"https:\/\/believeindustry.company\/heavy-duty-step-beam-roll-forming-thick-coil\/"},"modified":"2026-11-04T22:03:07","modified_gmt":"2026-11-04T14:03:07","slug":"heavy-duty-step-beam-roll-forming-thick-coil","status":"publish","type":"post","link":"https:\/\/believeindustry.company\/tr\/heavy-duty-step-beam-roll-forming-thick-coil\/","title":{"rendered":"A\u011f\u0131r Hizmet Step Beam Haddeleme: Kal\u0131n Kangal \u0130\u00e7in 6 Kural"},"content":{"rendered":"\t\t
\n\t\t\t\t\t\t
\n\t\t\t\t\t\t
\n\t\t\t\t\t
\n\t\t\t
\n\t\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t

Heavy Duty Step Beam Roll Forming: Thick Coil and High-Strength Steel<\/h1>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Short answer:<\/strong> Heavy duty step beam roll forming starts at 3.0 mm strip and runs to 5.0 mm, with 6.0 mm on request. Moving up from a standard line is not a motor upgrade. Shaft diameter, roll diameter, stand count, punch tonnage and cut-off type all change together, and line speed roughly halves.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

A 2.5 mm step beam line and a 5.0 mm step beam line can be quoted at similar machine length. Run thick coil through the light one and the gap shows in the first bundle: bowed webs, torn hole edges, and shafts that deflect under load.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

This guide covers what changes when heavy duty step beam roll forming moves into the 3.0 to 5.0 mm band, and which of those changes belong in the purchase order.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t

\n\t\t\t\t\t\t
\n\t\t\t\t\t
\n\t\t\t
\n\t\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t

What Heavy Duty Step Beam Roll Forming Covers<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

In heavy duty step beam roll forming, duty is a thickness and depth pair, not a marketing label. Published rack load tables separate the bands below, and the machine follows the band rather than the other way round.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t
\n\n\n
Class<\/th>Strip thickness<\/th>Beam depth<\/th>Load per beam pair<\/th>Typical system<\/th><\/tr>\n<\/thead>\n
Light<\/td>1.5 to 2.0 mm<\/td>80 to 120 mm<\/td>1,000 to 1,500 kg<\/td>Selective racking, retail<\/td><\/tr>\n
Standard<\/td>2.0 to 3.0 mm<\/td>100 to 160 mm<\/td>1,500 to 2,500 kg<\/td>Distribution centre<\/td><\/tr>\n
Heavy duty<\/td>3.0 to 5.0 mm<\/td>140 to 200 mm<\/td>2,500 to 4,500 kg<\/td>Drive-in, double deep, high bay<\/td><\/tr>\n
Extra heavy<\/td>5.0 to 6.0 mm<\/td>180 to 250 mm<\/td>4,500 kg and above<\/td>Mezzanine, crane access, export racking<\/td><\/tr>\n<\/tbody>\n<\/table><\/div>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Two consequences follow for heavy duty step beam work. Above 4.0 mm the beam usually takes a welded end plate instead of a notched connector, because the notch removes too much of the load path. And the coil grade stops being a purchasing detail, since a 4.0 mm section in the wrong grade will crack at the step radius no matter how the rolls are set.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"Finished\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t
\n\t\t\t\t\t\t
\n\t\t\t\t\t
\n\t\t\t
\n\t\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t

Where Thick Coil Breaks a Standard Line<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Bending force scales with thickness squared at a fixed bend radius. That is why heavy duty step beam roll forming jumps so hard from 2.5 mm to 5.0 mm: four times the force, same bend radius.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Roll shafts carry that force across a fixed span, and deflection falls with the fourth power of diameter. A shaft holding 0.10 mm of deflection at 2.5 mm strip needs about 1.4 times the diameter at 5.0 mm, which in practice turns an 80 mm shaft into 110 or 120 mm. Frame, bearing housing, and gearbox grow with it.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t
\n\n\n
Item<\/th>1.5 to 2.5 mm line<\/th>3.0 to 5.0 mm line<\/th><\/tr>\n<\/thead>\n
Shaft diameter<\/td>65 to 80 mm<\/td>95 to 120 mm<\/td><\/tr>\n
Roll outside diameter<\/td>180 to 220 mm<\/td>260 to 340 mm<\/td><\/tr>\n
Forming stands<\/td>20 to 26<\/td>28 to 34<\/td><\/tr>\n
Drive per stand group<\/td>5.5 to 7.5 kW<\/td>11 to 18.5 kW<\/td><\/tr>\n
Line speed<\/td>18 to 25 m\/min<\/td>8 to 15 m\/min<\/td><\/tr>\n
Punch capacity<\/td>40 to 60 t<\/td>120 to 200 t<\/td><\/tr>\n
Cut-off<\/td>Flying shear<\/td>Flying saw<\/td><\/tr>\n
Decoiler<\/td>5 to 10 t<\/td>10 to 15 t<\/td><\/tr>\n<\/tbody>\n<\/table><\/div>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Speed is the number buyers notice first. A heavy duty step beam roll forming line runs at roughly half the strip speed of a light line, and no amount of motor power closes that gap, because the limit is metal flow at the bend, not torque.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t

\n\t\t\t\t\t\t
\n\t\t\t\t\t
\n\t\t\t
\n\t\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t

Steel Grade: Q345, S355MC, and Why G550 Stops at 1.2 mm<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

The G550 question comes up on nearly every heavy duty step beam enquiry, and the answer is short. G550 coil is supplied thin. BlueScope quotes 0.45 to 1.2 mm base metal thickness, AS 1397 sets minimum elongation at 2 percent, and the same standard permits forming only at a generous bend radius. There is no 4.0 mm G550 step beam because there is no 4.0 mm G550 coil.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t
\n\n\n
Grade<\/th>Standard<\/th>Yield<\/th>Usual thickness<\/th>Note for heavy beams<\/th><\/tr>\n<\/thead>\n
Q235B<\/td>GB\/T 700<\/td>235 MPa<\/td>1.5 to 4.0 mm<\/td>Cheapest option, needs paint or galvanizing<\/td><\/tr>\n
Q345B<\/td>GB\/T 1591<\/td>345 MPa<\/td>2.0 to 5.0 mm<\/td>Default grade on Chinese heavy beam lines<\/td><\/tr>\n
S355MC<\/td>EN 10149-2<\/td>355 MPa<\/td>2.0 to 5.0 mm<\/td>Most consistent springback, preferred for export racking<\/td><\/tr>\n
S420MC<\/td>EN 10149-2<\/td>420 MPa<\/td>2.0 to 4.0 mm<\/td>More overbend and faster roll wear<\/td><\/tr>\n
G550<\/td>AS 1397 \/ S550GD<\/td>550 MPa<\/td>0.4 to 1.2 mm<\/td>Not available thick, 2 percent elongation<\/td><\/tr>\n<\/tbody>\n<\/table><\/div>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

For heavy duty step beam work at 3.0 to 5.0 mm, the practical choice sits between Q345B and S355MC. Both hold 15 to 22 percent elongation, which is what a step radius of 1.5 times thickness needs. S355MC costs more per tonne and returns it in repeatability, because a mill certificate with a narrow yield band means the overbend setting stays valid from coil to coil. That matters when a line runs the same beam for months.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

S420MC is worth it above 200 mm depth where the load table is tight. Expect 20 to 30 percent more forming force and a shorter roll life.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t

\n\t\t\t\t\t\t
\n\t\t\t\t\t
\n\t\t\t
\n\t\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t

Punching 3 to 6 mm Strip<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Holes still go in before forming on any heavy duty step beam line, for the reason covered in our step beam production process guide<\/a>: flat strip sits on a solid die and the hole edge stays clean. What changes is tonnage.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t
\n\n\n
Hole diameter<\/th>3.0 mm<\/th>4.0 mm<\/th>5.0 mm<\/th>6.0 mm<\/th><\/tr>\n<\/thead>\n
14 mm<\/td>18 t<\/td>24 t<\/td>30 t<\/td>36 t<\/td><\/tr>\n
18 mm<\/td>23 t<\/td>31 t<\/td>39 t<\/td>46 t<\/td><\/tr>\n
22 mm<\/td>28 t<\/td>38 t<\/td>47 t<\/td>57 t<\/td><\/tr>\n<\/tbody>\n<\/table><\/div>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Size the press for the largest hole in the mix, then add 25 to 30 percent. A press working at its rated tonnage deflects, the die wears unevenly, and slug pull starts long before anything looks broken.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Die clearance runs 8 to 12 percent of thickness per side, so 3.0 mm strip wants 0.25 to 0.35 mm and 6.0 mm strip wants 0.50 to 0.70 mm. Tight clearance raises punch wear on high strength steel. Loose clearance produces a torn edge that a connector pin will not seat against.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Alignment checks that keep a die alive are the same at any thickness, and our punching die installation guide<\/a> lists the sequence.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"Servo\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t
\n\t\t\t\t\t\t
\n\t\t\t\t\t
\n\t\t\t
\n\t\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t

Forming Strategy: Stations, Overbend and Edge Cracking<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

A heavy duty step beam roll forming line needs 28 to 34 stands. The extra stands over a standard line are not for the profile, they are for load distribution. Ten or eleven break the flange and lip at 15 to 20 degrees per pass, fourteen bring the section to shape, and four to six sizing stands correct what the earlier passes left.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Springback is where most heavy duty step beam first runs fail. S355 springs back 40 to 60 percent more than Q235 at the same radius, so the final passes overbend two to four degrees past 90 and let the steel recover into square. A line tuned on Q235 will run every S355 beam with flanges sitting open.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Minimum inside radius drives cracking. At 4.0 mm strip, 1.5 times thickness means a 6 mm inside radius. A drawing that calls for 4 mm cracks the outer fibre on the first pass, and no lubricant fixes it. Change the drawing or change the grade.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Rolls for heavy duty step beam tooling run GCr15 at HRC 58 to 62, with chrome or hard-chrome finish on the last sizing stands to stop marking. Surface pressure on 5.0 mm coil is roughly double the light-line figure, so roll marks appear where a lighter line would run clean.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t

\n\t\t\t\t\t\t
\n\t\t\t\t\t
\n\t\t\t
\n\t\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t

Cut-Off, Tolerance and Coil Logistics<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

A 5.0 mm section cannot be sheared cleanly on a light frame. Shear force for a 300 mm wide strip at 5.0 mm and 450 MPa runs near 675 kN, which is 67 t at the blade.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Heavy duty step beam lines cut with a flying saw: carbide blade, 8 to 15 m\/min, burr under 0.1 mm, cut length held to plus or minus 1.5 mm. A shear still works below 4.0 mm, and the step beam vs box beam comparison<\/a> covers where each section type lands.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Coil logistics decide the shift. A 12 t coil of 300 mm by 5.0 mm strip holds about 1,019 m, which is 85 minutes of running at 12 m\/min. The same coil in 3.0 mm holds 1,697 m and runs 141 minutes. In heavy duty step beam roll forming, a 15 t decoiler with a coil car is not a luxury, it is the difference between three and five coil changes per shift.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Output in heavy duty step beam roll forming follows the same arithmetic. A 6 m beam needs 30 seconds of forming at 12 m\/min, plus punch and cut time, so a well-run heavy line turns out 80 to 110 beams per 8 hour shift. The stacker usually sets that number, not the mill.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"Hydraulic\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t<\/section>\n\t\t\t\t
\n\t\t\t\t\t\t
\n\t\t\t\t\t
\n\t\t\t
\n\t\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t

What to Put in the Enquiry<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Five numbers separate a heavy duty step beam quotation from a guess:<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t