What Is a Cable Tray Roll Forming Machine? Types and Specs

Darren Mao
Kasım 15, 2026

Projeniz için bir Profil Makinesi mi gerekiyor?

Believe Industry'dan ücretsiz teklif alın — 15 yılı aşkın özel profil bükme makinesi imalatı.

What Is a Cable Tray Roll Forming Machine? How It Works, Types and Specs

Keywords: cable tray roll forming machine, perforated cable tray, ladder cable tray, trough cable tray, roll forming line speed, cable tray machine specs, punching unit, cassette changeover

Short answer

A cable tray roll forming machine is a continuous production line that turns steel coil into finished cable tray sections. The strip passes through a leveler, a servo feeder and punch press, a row of forming rolls, and a cut off unit. It leaves the line as a U shaped or C shaped tray at the programmed length, ready for supports and covers.

The cable tray roll forming machine works with galvanized steel, stainless steel and aluminum in 0.8 to 2.5 mm thickness and 100 to 600 mm strip width. Ladder tray needs rung welding on top of forming, so it uses a different line layout. That distinction matters more than a headline speed number when you request a quote.

A press brake bends one part at a time. A cable tray roll forming machine bends the strip gradually across 12 to 22 stands, so the section stays consistent over 3 m or 6 m lengths.

What is a cable tray roll forming machine?

A cable tray roll forming machine is a cold forming line. It does not heat the metal. Each pair of rolls takes a small bend until the flat strip reaches the final profile. The number of stands depends on the section. A shallow C channel needs fewer stands than a deep ventilated trough with return flanges.

Cable tray roll forming machine definition: a cable tray roll forming machine is a continuous cold roll forming line with 12 to 22 powered stands that shapes galvanized, stainless or aluminum strip into trough, perforated, solid bottom or channel cable tray, then cuts it to length while the strip keeps moving.

Bu NEMA VE 1 classification used in North America separates ladder, ventilated trough, solid bottom and channel tray. The IEC 61537 standard used across Europe, the Middle East and Asia covers cable tray and cable ladder systems with a different vocabulary. Both documents describe the product. The cable tray roll forming machine is the equipment that makes the product.

Figures in this article come from cable tray lines delivered by Believe Industry to more than 50 countries since 2005, plus the standards listed above. They are shop figures, not catalogue claims. Where a range is wide, the reason is the hole pattern or the number of widths a plant runs.

İstasyon	Ne yapar	Typical figure	Neden önemli
Açıcı	Holds the coil and pays off strip	3 to 8 t coil	Coil weight sets how often the line stops
Doğrultucu	Flattens coil set before punching	5 to 9 rolls	Flat strip keeps hole position stable
Servo Besleyici ve Punch Presi	Indexes strip and punches slot patterns	3 to 8 m/min with punching	Punching usually sets the line speed
Roll forming stands	Bends strip into the tray section	12 to 22 stands	Deep sections and return flanges need more
Cut off unit	Cuts the moving profile to length	plus/minus 1 mm servo, plus/minus 3 mm hydraulic	Length tolerance shows up at installation
Run out table and stacker	Collects and stacks finished lengths	15 to 25 m/min stacking	Stacker capacity limits sustained output

How a cable tray roll forming machine works

The coil sits on a decoiler. A leveler removes coil set, because strip that curls will not punch in the same place twice. A servo feeder then indexes the strip into a punch press. The press cuts ventilation slots, mounting holes and splice holes before the metal is bent. Punching first is easier. The strip is still flat, so a single die set can serve the whole bottom panel.

After punching, the strip enters the forming stands. Each stand has an upper and lower shaft with shaped rolls. The bend increases gradually from one stand to the next. A perforated tray with return flanges may need 18 to 22 stands. A simple C channel tray may need 12 to 14. The cable tray roll forming machine keeps the strip under slight tension between stands so the punched holes do not stretch out of position.

At the exit, an encoder measures length and triggers the cut off unit. A hydraulic cut off slows or stops the strip for each cut. A flying shear or flying saw tracks the moving profile and cuts while it travels, so the cable tray roll forming machine never has to stop. Our uçan makas kılavuzu explains the two drive types and the length accuracy each one gives.

For Russian type tray, an end expanding unit opens the last 100 mm of each length so two sections join without a separate coupler. That station adds cost, but it removes one part from every joint on site.

Punching, dies and hole patterns

Punching is the station that decides how fast a cable tray roll forming machine can run. A hydraulic press with a servo feeder works in steps. The feeder advances one pitch, the press closes, the feeder advances again. At 12 pitches per metre and a 1.2 second press cycle, the arithmetic gives about 4 m/min. Faster presses help, but the physics does not change much.

A rotary punch uses a rotating die cylinder and punches while the strip keeps moving. It suits one repeating slot pattern at 10 to 15 m/min. It costs more and it is less flexible. A plant that sells ten hole patterns is usually better off with a press and ten die sets.

Die sets are per pattern, not per machine. Slot width, pitch, edge distance and side hole positions all live in the die. Ask the supplier to list every die set in the quotation, along with the spare punch list and the expected regrind interval. A cable tray roll forming machine quoted with one die set will not produce a second pattern without a second invoice.

Four tray types that do not share one machine

Buyers often ask for one cable tray roll forming machine that makes every tray type. Four common sections need different tooling and sometimes different stations. The table below uses the section names found in NEMA VE 1 and in the Metal Konstrüksiyon Derneği technical library.

Tava tipi	Bölüm	How the machine makes it	Ek istasyon	Usual width
Solid bottom trough	U with a flat bottom	Forming stands only	Yok	100 to 600 mm
Ventilated or perforated trough	U with slots in bottom and sides	Punch press before forming	One die set per hole pattern	100 to 600 mm
Merdiven Tavası	Two side rails plus welded rungs	Forms side rails, then feeds rungs	Rung feeder and welder	200 to 900 mm
Channel tray	Shallow U or C, single piece	Fewer forming stands	Yok	50 ila 300 mm

A cable tray roll forming machine built for perforated tray has punch dies matched to one hole pattern. Change the pattern and you change the die set. Change the width and you adjust or swap the forming rolls. A ladder tray line adds a welder, which a trough line does not have. Our merdiven ve delikli tava karşılaştırması goes through the production differences section by section.

Wire mesh tray is a fifth category. It is welded from wire, not roll formed from strip. A cable tray roll forming machine does not make it, and a supplier who says otherwise is describing two different factories.

Line speed: why 60 m/min and 4 m/min both appear in quotes

This is the number that causes the most confusion. A supplier quoting 60 to 70 m/min is usually quoting the forming rolls running without punching and without a cut cycle. A plant running perforated tray at 3 to 6 m/min is quoting real output with an inline press. Both figures can be true for the same cable tray roll forming machine.

Figure on the quote	What it measures	Tipik aralık	Limiting station
Forming roll surface speed	Rolls only, no punch or cut	30 ila 60 m/dak	Drive and tooling design
Line speed with inline punch press	Whole line, press indexing each pitch	3 to 8 m/min	Press stroke and feed time
Line speed with rotary punching	Whole line, continuous punching	10 ile 15 m/dk	Die circumference
Line speed with flying cut off	Whole line, non stop cutting	10 ila 20 m/dk	Cut carriage travel
Sustained shift output	Saleable metres per hour after changeover	3 to 15 m/min equivalent	Coil changes, stacking, scrap

Ask for the number as saleable metres per shift on your own coil, with your hole pattern. The MHI guidance on throughput is a useful reference for defining output before a factory acceptance test. The how to choose a roll forming machine guide has a worked example of the same calculation.

Two more things move real output. Hole pitch sets the press cycle. Coil weight sets how often the line stops for a new coil. A cable tray roll forming machine with a 3 t coil and 12 punch strokes per metre will never match a line with an 8 t coil and 6 strokes per metre, even if the brochure speed is identical.

Materials and finishes

Pre galvanized strip is the default for indoor tray. The zinc layer is already on the coil, so the cable tray roll forming machine has to avoid scratching it. Polished rolls and a clean run out table matter more here than extra power.

Hot dip galvanized tray is formed from bare steel and dipped afterwards. That route needs a cut end that can drain and a profile that does not trap zinc. It also needs a jig at the dip plant, which is a different business from forming.

Stainless 304 and 316 are common in food plants, marine work and Middle East outdoor projects. Stainless work hardens faster than mild steel, so stand spacing and roll geometry change. Aluminum is lighter and easy to form, but it marks easily and needs a different roll surface finish. The engineering reference on metal properties is a reasonable starting point for comparing these grades.

Typical specifications to put in an enquiry

A useful enquiry sheet pins down the section, the holes and the length before it asks for a price. The ranges below come from cable tray roll forming machine projects delivered by Believe Industry since 2005. They are starting points, not a substitute for a profile drawing.

Kalem	Usual range	Not
Şerit kalınlığı	0.8 to 2.5 mm	3.0 mm needs heavier stands and more power
Şerit genişliği	100 to 600 mm	Russian type lines cover this in one cassette set
Tray height	25 to 150 mm	Deep sections need more forming stands
Malzeme	Galvanized steel, stainless 304 or 316, aluminum	Stainless work hardens faster
Şekillendirme standları	12 to 22	Count grows with return flanges
Delme	Hydraulic press or rotary punch	One die set per hole pattern
Kesim boyu toleransı	plus/minus 1 mm servo, plus/minus 3 mm hydraulic	Measured on 3 m parts
Kesim boyu	2 to 6 m	Standard export lengths are 3 m and 6 m
Size changeover	20 to 40 min auto width, 2 to 3 h cassette	Punch dies are a separate swap
Installed power	45 to 110 kW	Depends on press and stand count
Line length	22 to 38 m	Include coil loading and run out space

Bu otomatik ebat değiştirmeli kablo tavası makinesi page shows how width adjustment works when a plant runs many widths. The cable tray roll forming machine product page lists the station layout for one delivered line. For budget planning, the rulo şekillendirme makinesi fiyatı article explains which scope items move the total.

How to spec a cable tray roll forming machine for your project

Start with the profile drawing and the standard that governs it. NEMA VE 1 and IEC 61537 do not use the same names for the same section. A dimensioned drawing removes the translation problem.

Fix the hole pattern next. Slot size, pitch and edge distance decide the die set, and the die set decides the press. The punching station is the part of a cable tray roll forming machine that most often sets the line speed.

Then fix the width range. One width can use fixed rolls. Several widths need manual spacers, a cassette set or motorised width adjustment. The Orta Doğu alıcı kılavuzumuz covers the cassette trade off for projects with many sizes.

Ask for a factory acceptance test on your own coil. Measure 20 consecutive parts, record length and hole position, and keep the signed report. Check the ISO 9001 and CE certificate scope and its dates. The Metal Konstrüksiyon Derneği publishes useful guidance on specifying metal products and finishes.

Finally, plan the bay. A cable tray roll forming machine is 22 to 38 m long. Coil loading space, service access on both sides and a level concrete floor matter as much as drive power. The Kazakhstan shipment report shows a complete line staged before dispatch.

Mistakes buyers make

Comparing brochure speeds without the hole pattern. The number is meaningless until the press cycle is fixed.

Buying one die set and expecting six hole patterns. Each pattern needs its own tooling, and punches wear.

Ignoring changeover. A plant that runs eight widths a week loses more time to roll changes than to cutting.

Skipping the factory acceptance test. Length tolerance and hole position are easy to measure before shipment and expensive to argue about after installation.

Assuming ladder tray comes off a trough line. The welder and rung feeder are separate stations. Every one of these mistakes shows up in the first month of a cable tray roll forming machine running in a real plant.

Sıkça Sorulan Sorular

Q: What is a cable tray roll forming machine used for?

It makes long metal tray sections from coil for carrying power and data cables in plants, data centres, tunnels and commercial buildings. One cable tray roll forming machine usually serves one section family, with a die set per hole pattern.

Q: Can one cable tray roll forming machine make both perforated and ladder tray?

Not from one tooling set. A perforated tray line has a punch press before the forming stands. A ladder tray line forms two side rails and welds rungs between them. Some plants share the decoiler and run out table, but the middle of the line is different.

Q: Bir kablo tavası rulo şekillendirme makinesi ne kadar hızlı çalışır?

With an inline punch press, 3 to 8 m/min of finished tray is normal. With rotary punching and a flying cut off, 10 to 20 m/min is realistic. The 60 m/min figure describes forming rolls with no punching. Ask for saleable metres per shift.

Q: What thickness can a cable tray roll forming machine handle?

0.8 to 2.5 mm covers most galvanized and aluminum tray. Stainless 304 and 316 work in the same range but need polished rolls and more power. A 3.0 mm heavy tray line needs a different stand and gearbox design.

Q: How long does size changeover take on a cable tray roll forming machine?

Motorised width adjustment takes 20 to 40 minutes. A cassette swap takes 2 to 3 hours. Punch dies are a separate change and can add another 1 to 2 hours. Ask the supplier to demonstrate the full change during the factory acceptance test.

Q: How much does a cable tray roll forming machine cost?

Scope drives the total more than the base machine. Punch dies, cassette sets, the flying cut off, stacker, freight and commissioning are separate lines on a quote. The rulo şekillendirme makinesi fiyatı article breaks down the scope table. Send a drawing and hole pattern before comparing numbers.

Where to go next

Bu cable tray roll forming machine product page has a delivered line layout with station positions. The merdiven ve delikli tava karşılaştırması helps if the section is still open. Either way, start from a dimensioned profile drawing and one hole pattern. That is the only input a supplier can quote against without guessing.

Last updated: 2026-11-15

Makale Değişiklik Kaydı

2026-11-15: Initial publication. Line workflow, punching and die sets, four tray type comparison, speed definitions, material notes, specification ranges and 6 FAQ.

Sonraki İnceleme Tetikleyicileri

NEMA VE 1 or IEC 61537 revision; new punching or cassette changeover figures from shipped lines; quarterly SERP check for the focus term; priced scope changes from suppliers.