flying hydraulic cutting device on the solar C U and top hat roll forming line

3 in 1 Roll Forming Machine Tested and Ready to Ship for Solar

Need a Roll Forming Machine for Your Project?
Get a free quote from Believe Industry — 15+ years of custom roll forming manufacturing.
Request a Quote Download Catalogue

3 in 1 Roll Forming Machine Passes Testing, Ready to Ship for Solar

A 3 in 1 roll forming machine has passed final testing in our workshop and is ready to ship to a solar mounting customer. One line forms C sections, U sections and top hat sections from a shared front end. Every station in the order is assembled, wired and run. This 3 in 1 roll forming machine is crated now and waiting for the truck.

Short answer: This 3 in 1 roll forming machine combines a 5 ton hydraulic uncoiler, a leveler, a servo feeder with multiple punch stations, an auto width adjustable roll forming machine, a cassette mill, a new motorized top and side roller adjustment, and a flying hydraulic cutting device. One line covers three solar profiles. Factory testing is complete and the machine is ready to ship.

What is in this 3 in 1 roll forming machine shipment

Seven stations make up the line. Each has one job on the solar strip. The table below lists the full scope of the order.

StationWhat it doesProfiles covered
5 ton hydraulic uncoilerHolds and feeds the steel coilC, U, top hat
LevelerFlattens coil set before formingC, U, top hat
Servo feeder and punch stationsFeeds to length and punches holesC, U, top hat
Auto width adjustable roll forming machineShapes the web and flanges to sizeC and U sizes
Cassette millChanges the tooling set per profileAll three
Motorized top and side roller adjustmentSets roll gaps for top hatTop hat
Flying hydraulic cutting deviceCuts to length while line runsC, U, top hat

The buyer gets one production line instead of three. A solar plant that needs mounting rails in C, U and top hat profiles can run all three from one coil entry and one control station. Our top hat roll forming machine page covers the single profile version of this tooling.

5 ton hydraulic uncoiler and leveler

The line starts with a 5 ton hydraulic uncoiler. The hydraulic expansion holds the coil tight on the mandrel. A motor drives the strip into the leveler at a steady rate. Heavy coils are common in solar mounting work, so the 5 ton rating gives the buyer room to run longer coils between changes.

5 ton hydraulic uncoiler with steel coil on the 3 in 1 roll forming machine

After the uncoiler, the leveler removes coil set. Flat strip is critical for a 3 in 1 roll forming machine, because three profiles share the same entry. A coil with curl will drift in the forming stands and show up as bow in the finished section.

leveler before the servo feeder and punch stations on the solar roll forming line

The uncoiler and leveler sit on one base frame. This keeps the 3 in 1 roll forming machine aligned from the first stand to the flying cut.

Servo feeder and multiple punch stations

A servo feeder pulls the strip to length and holds it while the punch stations work. Solar mounting sections need slots and round holes at set pitches. Multiple punch stations cut these in one pass, so the 3 in 1 roll forming machine does not stop between holes.

servo feeder and multiple punch stations on the solar roll forming line

Punch pitch is set in the controller. The operator calls up a recipe for C, U or top hat and the feeder follows that pitch. Hole position is checked against the formed profile, not the flat strip, because forming moves the metal. Our punch die installation guide explains that alignment check in detail.

Auto width adjustable roll forming machine

Solar projects call for several web widths. The auto width adjustable roll forming machine changes the web width from the control panel. The operator enters the target size and the stands move to position. No shims and no manual measuring on every change.

roll forming part for U section with some cassette removed to show the tooling on the 3 in 1 roll forming machine

The photo shows the U section forming part with part of the cassette removed. This exposes the roller setup for inspection. The auto width function handles C and U sizes across the order book. A similar approach is used on our automatic size change machine, where width changes happen without a tooling swap.

Cassette mill for different profiles

The cassette mill is the heart of this 3 in 1 roll forming machine. Each profile has its own cassette of rolls. To switch from C to U to top hat, the operator swaps the cassette set. The stands stay in place. Only the roll tooling changes.

cassette mill for top hat section on the solar 3 in 1 roll forming machine

Cassette tooling protects the investment made by the buyer. Three separate lines would need three sets of stands, three drives and three floor footprints. One 3 in 1 roll forming machine with three cassettes needs one of each. The tradeoff is that one profile runs at a time, which suits a solar plant that batches its mounting sections by project.

New motorized top and side rollers adjustment

Top hat sections need tight control of the web and both flanges. The new design on this 3 in 1 roll forming machine uses motorized top rollers and motorized side rollers. The operator sets the roll gaps from the control panel instead of turning screws by hand.

motorized top and side rollers adjustment for quick top hat section changeover
motorized top rollers adjustment for top hat section on the 3 in 1 line

This is the main upgrade in the order. On a manual line, setting the top hat gaps across ten stands takes time and skill. With motor adjustment, the recipe stores the gap values and repeats them on the next run. Changeover time drops and the first good part comes sooner.

The C section forming part uses the same frame and drive as the other cassettes. The photo below shows the C section tooling installed on the line during the test run.

roll forming part for C section on the solar 3 in 1 roll forming machine

Flying hydraulic cutting device

The last station is a flying hydraulic cutting device. It travels with the strip while the cut happens, so the 3 in 1 roll forming machine does not stop for each piece. Cut length comes from the encoder on the servo feeder and is confirmed at the flying saw.

flying hydraulic cutting device on the solar C U and top hat roll forming line

Flying cut protects the profile ends. A stop and cut setup can dent a thin solar section or leave a burr. A flying cut keeps the line moving and gives a clean square end on C, U and top hat alike.

Testing complete, ready to ship

The full line has been assembled and tested in our workshop. Each station was run, not just wired. The table below shows what we checked before release.

CheckMethodResult
Coil feed and levelingRun coil through uncoiler and levelerPassed
Punch pitchMeasure hole pitch on sample stripPassed
Auto width changeChange width from panel and measurePassed
Cassette swapSwap C, U and top hat cassettesPassed
Motorized roll gapsSet top hat gaps by recipePassed
Flying cut lengthCut three lengths per profilePassed

Test pieces from all three profiles are packed with the machine as first article samples. Our engineers will install and commission this 3 in 1 roll forming machine at the customer site, then run the same checks again on the production coil.

Why one line for three solar profiles

Solar mounting uses C purlins, U channels and top hat rails across one project. Buying three lines ties up capital and floor space. This 3 in 1 roll forming machine gives the buyer three profiles with one uncoiler, one drive train and one control station. The solar tracker profile guide shows how mounting sections differ by application, and the solar mounting frame shipment report covers a related install.

Profile choice follows the drawing. Web height, flange width and hole pattern come from the solar structure designer. Steel grades and section properties can be cross checked with engineering references. Mounting systems that need a listed racking assembly are reviewed against UL requirements, and project scale is tracked in solar program data. For background on the base sections, see our strut channel guide and the cost factors page.

Planning a similar order? Send your three profile drawings, coil width and thickness range, and your target output. We will return a line layout and a fixed price for the station mix that fits your solar work.

Believe Industry has built custom roll forming lines since 2005. 80+ engineers, 500+ projects, machines in 50+ countries, ISO 9001 and CE certified.

Frequently Asked Questions of 3 in 1 Roll Forming Machine

Q: What profiles does this 3 in 1 roll forming machine make?

A: It forms C sections, U sections and top hat sections for solar mounting. Each profile has its own cassette set on the same line.

Q: Is the machine tested before it ships?

A: Yes. The full line was assembled and run in our workshop. We checked coil feed, punch pitch, auto width change, cassette swap, motorized roll gaps and flying cut length. All passed, and sample pieces ship with the machine.

Q: Can all three profiles run at the same time?

A: No. One 3 in 1 roll forming machine runs one profile at a time. The operator swaps the cassette and calls the matching recipe on the controller.

Q: How does the auto width adjustment work?

A: The operator enters the target web width on the panel. The stands move to the new position without shims or manual measuring. It covers the C and U sizes in this order.

Q: What is new about the top hat roller adjustment?

A: Both the top rollers and the side rollers move by motor. Gap values are stored in the recipe and repeat on the next run, which cuts changeover time and gets to the first good part faster.

Q: Does the price include installation?

A: Yes. Our engineers install and commission the line at the customer site and repeat the factory checks on production coil before handover.

Last updated: 2026-11-19

Article Changelog

2026-11-19: First published. Company news on a 3 in 1 roll forming machine for C, U and top hat solar sections, tested and ready to ship, with the seven station breakdown, the new motorized top hat adjustment and six buyer FAQs.

Next Review Triggers

Confirmation of arrival and commissioning at the customer site, any change to the motorized roller adjustment design, a new profile added to the cassette mill, or a revision to the solar mounting profile drawings.

Table of Contents

New Updates